Does SCCM use port 8005?
SCCM use port 8005, and so was McAfee product. why Microsoft would use this port? Would MS be mindful of a well know port McAfee uses? Suggestions(provided by kevmjohnston and Jason Sandys):
- 67 UDP. PXE Distribution Point.
- 68 UDP. PXE Distribution Point.
- 69 UDP. PXE Distribution Point.
- 80 TCP. Distribution Point, Fallback Status Point, Management point,
- 443 TCP. Distribution Point, Management point (secure)
- 4011 UDP. PXE Distribution Point.
- 8530 TCP. Software Update Point.
- 8531 TCP.
Since today, the port 8005 is used for a Windows System Process. When i try to acces to the url http:localhost:8005 ,i can see a Blank Web Page, with no code and no info from any Web Server (No welcome web page or similar). With the netstat command i can see that the process that uses this port is System process.
SCCM documentation says that the following ports have to be opened for Remote Control: TCP – 135. TCP – 2701. TCP – 2702.
#1) SMB traffic on TCP 445 is a requirement for the SCCM Primary to communicate with the SCCM Secondary site server.
This is a little tool I created for testing the required TCP ports on SCCM client systems. It will check that the required inbound ports are open and that the client can communicate to its management point, distribution point and software update point on the required ports.
...
On the SCCM Server with the SUP role, open IIS Manager.
- Expand Sites.
- right-click the Web site.
- and then click Edit Bindings.
"8080" was chosen since it is "two 80's", and also because it is above the restricted well known service port range (ports 1-1023, see below). Its use in a URL requires an explicit "default port override" to request a web browser to connect to port 8080 rather than the http default of port 80.
- Download TCPView(only 285kb) from following link. ...
- Extract folder and start TCPView application.
- Right click on java.exe(because 8009,8005 ports are commonly used by java process) and select End Process option.
What port is 8009?
Apache JServ Protocol (AJP) is used for communication between Tomcat and Apache web server. This protocol is binary and is enabled by default. Anytime the web server is started, AJP protocol is started on port 8009. It is primarily used as a reverse proxy to communicate with application servers.
To remotely administer a client computer from the Configuration Manager console. In the Configuration Manager console, choose Assets and Compliance > Devices or Device Collections. Select the computer that you want to remotely administer and then, in the Home tab, in the Device group, choose Start > Remote Control.
You have two options to authenticate with your SCCM server: using server credentials or your Windows credentials. Server Authentication - selecting this method will require you to specify your User name and Password credentials, the ones set for your SCCM server.
To enable remote control and configure client settings
In the Configuration Manager console, choose Administration > Client Settings > Default Client Settings. On the Home tab, in the Properties group, choose Properties. In the Default dialog box, choose Remote Tools.
On a Windows computer
Press the Windows key + R, then type "cmd.exe" and click OK. Enter "telnet + IP address or hostname + port number" (e.g., telnet www.example.com 1723 or telnet 10.17. xxx. xxx 5000) to run the telnet command in Command Prompt and test the TCP port status.
Type "Network Utility" in the search field and select Network Utility. Select Port Scan, enter an IP address or hostname in the text field, and specify a port range. Click Scan to begin the test. If a TCP port is open, it will be displayed here.
The easiest way to ping a specific port is to use the telnet command followed by the IP address and the port that you want to ping. You can also specify a domain name instead of an IP address followed by the specific port to be pinged. The “telnet” command is valid for Windows and Unix operating systems.
PXE uses DHCP ports and TFTP to download the binary files. For TFTP and DHCP, you need to enable ports 67, 69, and 4011. The TFTP and multicast servers use ports in the range 64001 through 65000 by default.
The Server Message Block protocol (SMB protocol) is a client-server communication protocol used for sharing access to files, printers, serial ports and other resources on a network. It can also carry transaction protocols for interprocess communication.
On the local machine, click the Start button and enter “CMD” in the search programs and files field. If the port 1433 is closed, an error will be returned immediately. If the port 1433 is open, you will be able to connect to the MS-SQL server.
What is PXE in SCCM?
PXE is an industry standard created by Intel that provides pre-boot services within the devices firmware that enables devices to download network boot programs to client computers. Configuration Manager relies on the Windows Deployment Services (WDS) server role via the WDS PXE provider.
The SMS Provider is a Windows Management Instrumentation (WMI) provider that assigns read and write access to the Configuration Manager database at a site. Each CAS and primary site require at least one SMS Provider. You can install more providers as needed.
| Port(s) | Protocol | Source |
|---|---|---|
| 8504-8553 | tcp,udp | IANA |
Port 80 is the default port. It's what gets used when no port is specified. 8080 is Tomcat's default port so as not to interfere with any other web server that may be running. If you are going to run Tomcat as your web server, the port can be changed to 80 so that visitors do not need to specify it.
You should not use port 8080 for https traffic. That port is conventionally used for non-secured data, akin to the use of port 80 for default external http. Port 8443 is the standard for Tomcat secured (SSL/TLS) data, corresponding to the common HTTPS port 443.
- Step 1: Find the connection's PID. netstat -ano | findstr :yourPortNumber. ...
- Step 2: Kill the process using it's PID. tskill yourPID. ...
- Step 3: Restart your server. ...
- Step 4: Stop your server properly.
By default, Tomcat listens on port 8080. However, if you want to configure Tomcat to listen on say, port 8081 as well, follow the steps below: Edit the server.
- Step 1 : Find Process id in windows using command prompt. netstat -ano | findstr <Port Number> netstat -ano | findstr <Port Number. ...
- Step 2 : Kill the process using command prompt. taskkill /F /PID <Process Id>
Port 8009 (and 8005) are just as important and should never be publically accessible. If for some reason the manager interface needs to be made available over the internet, Tomcat allows filtering access by IP address. This should be combined with a strong passphrase in the event of a spoofing attack.
| Port | Type |
|---|---|
| 8008 | TCP |
| 8009 | TCP |
| 53 | UDP |
| 1900 | UDP |
What is an AJP port?
AJP Connectors work in the same way as HTTP Connectors, but they use the AJP protocol in place of HTTP. Apache JServ Protocol, or AJP, is an optimized binary version of HTTP that is typically used to allow Tomcat to communicate with an Apache web server.
Introduction to remote control in Configuration Manager
Configuration Manager also lets you configure client settings to run Windows Remote Desktop and Remote Assistance from the Configuration Manager console.
In this article, you'll learn about the SCCM Remote Software Center in Right Click Tools. With Remote Software Center tool, you can view and install deployed applications, programs and software updates, and run/view task sequences on remote computers.
SCCM client push installation accounts require local admin privileges to authenticate to a machine and install the SCCM client. This means that NTLM authentication coerced using this technique will often have local admin privileges on all SCCM clients in the site.
When you enable SCCM enhanced HTTP configuration, the site server generates a self-signed certificate named SMS Role SSL Certificate. Here are the steps to access the SMS Role SSL Certificate.
The cloud management gateway (CMG) provides a simple way to manage Configuration Manager clients over the internet. You deploy CMG as a cloud service in Microsoft Azure. Then without more on-premises infrastructure, you can manage clients that roam on the internet or are in branch offices across the WAN.
Overview. Remote Desktop Protocol (RDP) is a Microsoft proprietary protocol that enables remote connections to other computers, typically over TCP port 3389.
Remoting In: SCCM - YouTube
Configure and Enable SCCM Remote Control - YouTube
What ports does Wsus use?
WSUS uses port 80 (Hypertext Transfer Protocol [HTTP]) and port 443 (Hypertext Transfer Protocol Secure sockets [HTTPS]) to communicate with Microsoft's servers. These ports must be open on your firewall to allow WSUS to synchronize updates.
What Ports Does WMI Use? WMI uses TCP port 135 and a range of dynamic ports: 49152-65535 (RPC dynamic ports – Windows Vista, 2008 and above), TCP 1024-65535 (RPC dynamic ports – Windows NT4, Windows 2000, Windows 2003), or you can set up WMI to use a custom range of ports.
The Server Message Block protocol (SMB protocol) is a client-server communication protocol used for sharing access to files, printers, serial ports and other resources on a network. It can also carry transaction protocols for interprocess communication.
The SMS Provider is a Windows Management Instrumentation (WMI) provider that assigns read and write access to the Configuration Manager database at a site. Each CAS and primary site require at least one SMS Provider. You can install more providers as needed.
PXE uses DHCP ports and TFTP to download the binary files. For TFTP and DHCP, you need to enable ports 67, 69, and 4011. The TFTP and multicast servers use ports in the range 64001 through 65000 by default.
Windows Update requires TCP port 80, 443, and 49152-65535. The IP address for the Windows Update web site constantly changes and it is not a fixed address.
| Port(s) | Protocol | Source |
|---|---|---|
| 8504-8553 | tcp,udp | IANA |
WMI is based on the Distributed Component Object Model (DCOM) which, by default, uses a randomly selected TCP port between 49152 and 65535 for communications.
WMI Provider Host shouldn't normally use much CPU, as it shouldn't normally be doing anything. It may occasionally use some CPU when another piece of software or script on your PC asks for information via WMI, and that's normal. High CPU usage is likely just a sign that another application is requesting data via WMI.
- Login to the Gateway.
- Type wbemtest in run window(Press Windows_key+r) and open wmi test window.
- Click on connect button in front of namespace.
- Enter \\<Target IP>\root\cimv2 in the namespace textbox and credentials of user used for discovery.
- Click connect.
- Click on query button after connection.
Does SCCM use smb1?
SCCM CB support both SMBv2 and SMB v3.
Unfortunately, more than a million Windows machines are still running the unpatched version of the SMBv1 protocol. Most are likely connected to a network, which makes other devices on the same network vulnerable, regardless of which SMB version they are using.
FTP is extremely fast and efficient compared to SMB when transferring large files. It can be difficult when it comes to small files, but overall, the speed of the FTP file transferring protocol is better. The use of short messages in SMB makes it sensible to network latency, which can decrease the speed.
- Launch Configuration Manager console.
- Navigate to Administration\Overview\Site Configuration\Sites.
- Select the Server, right click and click Properties.
- On Site Properties window, click General.
- Look for SMS Provider Location.
An SMS gateway is a website that allows users to send SMS messages from a web browser to people within the cell served by that gateway. An SMS gateway can also serve as an international gateway for users with roaming capability, allowing SMS communication away from the home network.
- Text Local. Text Local is one of the largest and most sought-after bulk messaging service providers. ...
- Fast2SMS. ...
- 2Factor. ...
- TextGuru. ...
- Exotel. ...
- Knowlarity. ...
- Value First. ...
- InfoBip.
