What means zero load?
Zero-load refers to a mutual fund that charges no commission or sales charge. Instead of using a secondary party shares are generally distributed directly by the investment company. Research has shown that there is little difference in the performance of zero-load funds in comparison to load funds.
Load funds are mutual funds that charge a sales fee or commission. No-load funds usually do not charge any sales fee or commission, as long as you keep your money invested for a specified period, often five years.
— The term “no-load mode” means the mode of operation when an external power supply is connected to the main electricity supply and the output is not connected to a load.
No load means no energy is delivered to the load. The load is essentially disconnected. Full load means the load consumes the maximum amount of energy of which it's capable. For example, if a light bulb is turned off it is in it's no load state.
The no-load current(Io) is the vector sum of the magnetizing current(Im) and no-load loss components current(Iw). The magnetising current(Im) is drawn by an induction motor to set up the magnetic flux in the air gap. The magnetizing current is responsible for setting up air gap power in induction motor.
No Load Current Formula
To calculate the no-load current, multiply the full load current by the percentage load factor over 100.
The best mutual fund is the one that helps you meet your investment objectives. But paying a load seriously hurts your potential returns, and you can get the same performance or better by using low-cost no-load funds. So there's no reason at all to pay more.
The open-circuit test, or no-load test, is one of the methods used in electrical engineering to determine the no-load impedance in the excitation branch of a transformer.
In a short circuit, there is no load. For many reasons, the wires in a circuit can find a short-cut, bypassing the load (and other components). Such a connection causes the same voltage from the cell to flow to the other end of the cell. When this happens, the high voltage causes the wires to heat up and catch fire.
The only reason to make electricity flow is to give it some work to do. This process of electricity doing work in a circuit is called load. Without having a load, or some work for electricity to do, then there is no point in having a circuit.
What is no load shutdown?
The no load shutdown feature works when the Battery Saver mode is enabled and the Back-UPS is in the On Battery mode. The Back-UPS will shutdown if the connected load draws less than 30 W of power for more than 5 minutes.
No-load mode means the condition in which the input of a power supply is connected to an AC source consistent with the power supply's nameplate AC voltage, but the output is not connected to a product or any other load.
Transformer “No-load” Condition: A transformer is said to be on “no-load” when its secondary side winding is open circuited, in other words, nothing is attached and the transformer loading is zero.
The no load voltage is the terminal voltage when zero current is drawn from the supply, that is, the open circuit terminal voltage. Some portion of voltage drops down due to internal resistance of voltage source.
To calculate the no-load voltage, multiply the full-load voltage by the load regulation, then add the full-load voltage to this result.
In the case of no-load, the secondary terminal of the transformer is open. There is no path available for the current to flow on the secondary side. Hence, the transformer does not draw current from the source.
no-load cost represents the cost of fuel required to keep the unit running. Such a mode of. operation is not possible for most thermal generating units. The no-load cost is simply the. constant term in the cost curve and does not have physical meaning.”
«No load running» means that there is no output torque available. In other words, the throttle is adjusted just enough to maintain the chosen rpm constant. «Full load running» means that there is the maximum torque that the engine can produced at the chosen rpm available at the crankshaft.
No-load current produces the magnetic flux and supplies the hysteresis and eddy current losses in the core. The no-load current (IE) consists of two components: the magnetizing current (Im ) and the core loss (IH).
Understanding a No-Load Fund
Because there is no transaction cost to purchase a no-load fund, all of the money invested is working for the investor. For example, if an investor purchases $10,000 worth of a no-load mutual fund, all $10,000 will be invested into the fund.
What is a disadvantage of buying a no-load fund?
The main disadvantage of a no-load fund is the lack of professional advice and guidance. You are responsible for processing the transaction, including analyzing and comparing the available options.
No-load funds generally don't provide investors with investment advice or direction because they don't charge a sales commission. Investors who prefer to work with a financial advisor or who might require assistance with their investment choices may find this to be a disadvantage.
No Load Test is an indirect method used for determining the efficiency and also to determine the circuit parameters of the equivalent circuit of the three-phase induction motors. The open-circuit test is performed on the transformer. The no-load test is the same as the open-circuit test performed on the transformer.
An open circuit implies that the two terminals are points are externally disconnected, which is equivalent to a resistance R=∞ . This means that zero current can flow between the two terminals, regardless of any voltage difference.
All electrical circuits require three components to operate: a source of power, a path for current, and a load. A source of electrical power can be a DC battery or an AC generator.
Electricity cannot flow without a power source (battery), and a load (bulb or resistor-electrical device/ component) and a closed conductive path (wires connecting it).
A load is any device that uses the energy of the flowing electricity. Typical loads are lights, motors, and appliances. When current flows through some load, either heat or a magnetic field is produced allowing the electrical energy to be converted into some type of other useful energy.
The source generates power, while the load consumes it. The rest of the circuit is simply formatting the electricity to travel properly to the load. By definition, a source is a device delivering energy into a system, while a load is a device extracting energy from a system.
Standard battery run time for a common UPS is around 5 to 10 minutes under full load and about twice that under half load. (Run times are often quoted as minutes under full and half load.)
No load operation should never exceed 15 minutes. For low load operation, you should contact your manufacturer or your account manager at Critical Power Supplies Ltd, who will be able to advise you on safe low load operation values and durations.
What is no load condition in power system?
A transformer is said to be on “no-load” when its secondary side winding is open circuited, in other words, nothing is attached and the transformer loading is zero.
If there is no load applied to the motor, the motor is not doing any work. However, if there is power being consumed by the motor, then we know this directly translates in to waste energy. The wasted energy is the energy that it takes to maintain rotational speed of the motor.
However, there is a difference between the two. Whereas the load-waived fund is a fund offered by an adviser or broker who might remove (waive) the load fee but keep others, such as the 12b-1 fee, a true no-load fund does not charge any load whatsoever and does not have any fees, including 12b-1 fees.
No-load mutual fund
A fund that charges no sales fees either on the front end (when you buy fund shares) or back end (when you sell fund shares).
Sanctioned (or Connected) Load is the total electricity supply that is provided to a meter. This is calculated in Kilo-Watt (or kW). It's the permissible total Kilo-Watt provided to a meter based on the devices connected to the meter.
(loʊd ) verb. If you load a vehicle or a container, you put a large quantity of things into it.
If you're doing your own research and making your own purchases or sales of mutual fund shares, you gain no benefit from buying load funds. You should generally buy no-load funds if you don't use an advisor, and buying no-loads can boost your returns by minimizing expenses.
In the electrical trades, the terms "line" and "load" are shorthand words that refer to the wires that deliver power from the source to a device (line), vs. those that carry power onward to other devices further along the circuit (load).
An electrical load is an electrical component or portion of a circuit that consumes (active) electric power, such as electrical appliances and lights inside the home. The term may also refer to the power consumed by a circuit. This is opposed to a power source, such as a battery or generator, which produces power.
An electrical load is simply any component of a circuit that consumes power or energy. In a household setting, the most obvious examples of electrical loads include light bulbs and appliances.
What is the load of a car?
Vehicle Load or Load Factor- is a ratio of the number of seats on a vehicle to the number of passengers.
Slang. to be intoxicated. See full dictionary entry for load.
used for telling someone to look at or listen to someone or something that you think is funny or interesting. Get a load of that dress! Synonyms and related words. Expressions used for telling someone to pay attention. right.
