Remote management by VTY access (Telnet/SSH) | N-Study (2024)

You can manage Cisco routers and Catalyst switches with a console connection, but this requires a direct console cable connection to the device you want to manage. Console connections are not an efficient way to manage remote devices. An efficient way to manage remote devices is to use VTY access, which is CLI-based remote access using Telnet or SSH.

Telnet uses TCP port number 23. Telnet is a simple protocol and does not encrypt communications. Therefore, there is a risk that if the communication is eavesdropped, the user ID/password account information can be compromised to allow a malicious user to login. On the other hand, SSH uses TCP port 22. It uses public key cryptography, which means that even if someone eavesdrops on SSH, there is no risk of account information being compromised.

To accept remote Telnet or SSH VTY access on Cisco routers and Catalyst switches, the VTY line must be configured in advance. The protocol to be accepted on the VTY line is specified by the transport input command.

Router(config)#line vty 0 4Router(config-line)#transport input ? all All protocols lapb-ta LAPB Terminal Adapter lat DEC LAT protocol none No protocols pad X.3 PAD rlogin Unix rlogin protocol ssh TCP/IP SSH protocol telnet TCP/IP Telnet protocol udptn UDPTN async via UDP protocol v120 Async over ISDN

You can specify a variety of protocols, but generally you should use telnet or ssh. If you want to accept only ssh, use transport input ssh. It is also possible to specify more than one protocol.

When you access a VTY , you are logging into a VTY line, a VTY line is a virtual interface that accepts VTY accesses and the line number is five, from 0 to 4 by default. The current IOS can be further extended to handle more VTY lines; a single device can accept multiple VTY accesses, and the assignment of a VTY line number uses the VTY line number available at the time the VTY access is received. When the line that sets up the authentication and the line that doesn’t set up the authentication are mixed together, it is not desirable from the security point of view, so please set up the authentication properly to all VTY lines basically.

Configuring Telnet access

To accept VTY access from a remote user, you basically have to authenticate; in the case of Telnet access, you can authenticate with a password on the VTY line or with a username/password defined by the router.

The login command enables the authentication on the VTY line by using the password set on the VTY line.

If you have enabled password authentication on the VTY line with the login command, but have not set a password on the VTY line, you will not be able to authenticate and VTY access will be denied as follows.

Password required, but none set

And for more flexible authentication, you can enter the login local command on the VTY line. This will allow you to authenticate with the username and password defined on the router.

We won’t go into the details here, but it is also possible to use an external authentication server for authentication.

If you input the no login command on the VTY line, you can access to VTY by Telnet without authentication. However, it is not recommended for security reasons because if you know your router’s IP address, anyone can access to Telnet.

To configure your router to accept SSH access, do the following

1. Domain name and host name configuration.
2. Generating a Public Key
3. Enable SSH and authentication on VTY
4. Configuring a user name and password

1.Domain name and host name configuration.

Configure the router with a unique domain name and host name to generate a public key to be used for encryption.

2.Generating a Public Key

Generates a public key. When you enter the command, you are asked for the bit length of the public key you want to generate. Enter the appropriate key bit length.

The following is an example of output from the crypto key generate rsa command for public key generation.

R1(config)#crypto key generate rsaThe name for the keys will be: R1.n-study.comChoose the size of the key modulus in the range of 360 to 2048 for your General Purpose Keys. Choosing a key modulus greater than 512 may take a few minutes.How many bits in the modulus [512]: 1024% Generating 1024 bit RSA keys, keys will be non-exportable...[OK]

3.Enable SSH and authentication on VTY

You can enable SSH on VTY. SSH is enabled by default by transport input all, so you don’t need to configure it.SSH requires username and password authentication. login local command to enable username and password authentication.

4.Configuring a user name and password

Configure the username/password for authentication.

Running Telnet from Cisco Router and Catalyst Switch

In addition to receiving Telnet access, Cisco routers and Catalyst switches can also telnet themselves to log in to other devices. To telnet to other devices, enter the following commands in user EXEC or privileged EXEC mode.

This command Telnet to a specified IP address or host name. To use the host name, you must be able to resolve the name by setting the ip host command or DNS.

You can omit the “telnet” command itself. In other words, if you enter an IP address or host name and press the “Enter” key, Telnet to the specified IP address or host name.

Here’s something to keep in mind. If you enter the wrong command, it will interpret the command as a hostname and try to resolve the name in order to telnet.

Router#aaa Translating "aaa"...domain server (255.255.255.255) (255.255.255.255)Translating "aaa"...domain server (255.255.255.255)% Unknown command or computer name, or unable to find computer address 

If you enter the wrong command “aaa”, the Cisco device interprets this as “Telnet to the host name “aaa””, and by default it will try to broadcast to perform name resolution for “aaa”. This action will cause the configuration process to be interrupted. To prevent this, enter the following command in global configuration mode

(config)#no ip domain-lookup

Router#configure terminal Enter configuration commands, one per line. End with CNTL/Z. Router(config)#no ip domain-lookupRouter(config)#end Router#aaa Translating "aaa" Translating "aaa"% Unknown command or computer name, or unable to find computer address 

If you enter the wrong command, no name resolution is performed and no time is lost. It is recommended that you include no ip domain-lookup during the configuration process.

Cisco routers and Catalyst switches can also provide VTY access to other devices as an SSH client. use the following commands in user EXEC or privileged EXEC mode to remotely log in to other devices as an SSH client.

This command will try to log in to the specified IP address or host with the specified user name. If you want to use the host name, you need to be able to resolve the name as well as the telnet command.

R2#ssh -l cisco 192.168.1.1Password:R1>

The ssh command also allows you to specify a variety of other options, such as version and encryption algorithms.

Enable log output for remote login destination (terminal monitor)

When you remotely log in to a Cisco router or Catalyst switch via Telnet/SSH, no logs are output by default. If you want to output the log of the remote login destination, enter the terminal monitor command in privileged EXEC mode.

Example of terminal monitor

The following is an example of the terminal monitor command. The following log output is obtained by telnetting from the console of R1 to R2, and if the terminal monitor command is not set up, the log will not be output even after exiting the global configuration mode at the R2 destination.

R1#telnet 192.168.12.2Trying 192.168.12.2 ... OpenUser Access VerificationPassword:R2>enablePassword:R2#conf tEnter configuration commands, one per line. End with CNTL/Z.R2(config)#exitR2#

When you exit global configuration mode after entering the terminal monitor command from privileged EXEC mode in R2, the log is displayed. Of course, the log is also displayed except when exiting the global configuration mode.

R2#terminal monitorR2#conf tEnter configuration commands, one per line. End with CNTL/Z.R2(config)#exitR2#*Mar 1 00:04:42.735: %SYS-5-CONFIG_I: Configured from console by vty0 (192.168.12.1)R2#

Suppose you have a VTY access from one Cisco device to another. when you have a VTY access, you become the CLI of the device to which you are accessing the VTY, and you can change configuration and execute show commands from the CLI. to abort the VTY access, you can use exit or logout You can enter a command to return to the original device’s CLI. However, this will cut off VTY access completely.

R1>exit [Connection to 10.1.1.1 closed by foreign host]Switch>

To suspend VTY access, press [Ctrl+Shift+6] and then press [x].

R1>[Ctrl+Shift+6] xSwitch# 

If you suspend a VTY access, use the show session command to show the VTY access you are keeping.

Switch#show session Conn Host Address Byte Idle Conn Name * 1 10.1.1.1 10.1.1.1 0 2 10.1.1.1 

The “*” indicates the last VTY access. The number after it is the session number. To resume a retained VTY access, use the resume command.

#resume <session-number>

When resuming, the resume command itself can be skipped. A session can be resumed if only the session number is specified. If you omit the session number, the session marked with an asterisk (*) is restarted. In other words, if you interrupt a session and come back to the original CLI, typing key without typing anything will return you to the previous session.

Switch#[Resuming connection 1 to 10.1.1.1 ... ] R1>

If you want to disconnect the VTY access you are holding, enter the following command.

#disconnect <session-number>

Verify VTY access

The following are the main commands to verify VTY access.

• show users
• show session

show users shows the VTY accesses to you. And show session shows the VTY accesses that you are making. Let’s look at the show users and show session in the following example network

First, if we look at the show users in R2, it looks like this

R2>show user Line User Host(s) Idle Location * 0 con 0 idle 00:00:00 18 vty 0 idle 00:00:03 10.1.1.1

This shows that R2 is telnetted from R1 (10.1.1.1). The “18” in “18 vty 0” is the overall line number, including the console, etc. The VTY line number is “0” in this example. If you want to force a telnet disconnect for yourself, use the clear line command. If you want to disconnect the Telnet connection in this example, use the VTY line number of the show users and enter the following

#clear line 18

You can then force a telnet disconnect from R1 to R2.

Next, if we look at the show session in R1, it looks like this

R1#show session Conn Host Address Byte Idle Conn Name * 1 10.1.1.2 10.1.1.2 0 0 10.1.1.2

R1 is telnetting to 10.1.1.2 (R2) and its session number is 1.