Adjusting Strat Pickup Height - SweetCare (2024)

How Pickups Work

Before making an adjustment, it’s good to know how your pickups are actually working in order to help you find the proper placement for them. The pickups in your Strat are basically small antennas that translate string vibration into an electrical signal. Inside your pickups are six magnets (pole pieces) wrapped in thousands of turns of copper wire. When the vibrating string is within the magnetic field of the guitar pickups, it disrupts the field, generating a small electric current. This small electric signal comes out of your guitar and into your amp, which is converted back into sound by the speaker.

Knowing how pickups work provides insight into how to properly adjust them.

Generally, the closer your pickups are to the strings, the greater the treble response and overall output. Unfortunately, there is no one-size-fits-all answer to the question of how high your pickups should be set. So when it comes to your own guitar, some experimentation is often necessary to find the best sound for you.

Adjusting Your Pickup Height

Now that you know the basics of how your pickup is working inside your guitar, it’s time to find a setting that works for you.

Each pickup is mounted onto the pickguard with a screw and spring on each side of the pickup. The screw head goes through the pickguard, passes through a spring, and threads into the ear of the pickup. Tightening the screw raises the height of the pickup, while loosening the screw will lower it into the body.

The screw and spring work together to properly set the pickup.

Mark the starting heights of the pickups on tape for future reference.

Having done this, grab an appropriately sized screwdriver and start making some adjustments. While you are doing this, it’s a good idea to keep in mind the following:

The Methodical Approach

In our methodical approach to pickup adjustment, we’re going to measure and record the starting positions of our pickups rather than use the tape-and-pencil method. This will allow you to set your pickups to a standard height and to communicate your final measurements to others. This is essential if you decide to take your guitar to a tech for a repair or setup and want the same string-to-pickup spacing when you get your guitar back.

Measuring Your Pickup Height

The standard way to measure your pickup height is to fret the guitar at the highest fret and measure from the top of the pole piece to the bottom of the string. This will allow for proper string clearance on every fret and string. Measuring pickup height in relation to the open string may result in certain notes fretting out in the higher frets. This happens because as you fret higher up the neck, the strings may lower far enough to hit the pole pieces and stop vibrating.Here at Sweetwater, our techs measure in increments of 32nds or 64ths of an inch. Depending on what type of ruler you have, you may want to use a different unit of measurement.

Precise pickup height measurements are crucial for proper string clearance.

Making the Adjustments

Once you’ve measured and recorded your starting heights, you will be ready to make some adjustments. So where to start? Our guitar techs here at Sweetwater recommend trying the following measurements as a good starting point for most Strat pickups. Remember, this is just a guideline. What should be the determining factor for your guitar’s pickup height is what sounds preferable to your playing style.

Start by setting all of your guitar pickups to 3/32” (0.093”, 2.38mm) on the bass side and 2/32” (1/16”, 0.0625”, 1.98mm) on the treble side. Remember, this is the space between the top of the pole piece and the bottom of the string, held down at the last fret. This should set your pickups at a reasonable “middle of the road” setting that should offer balanced output from each pickup.

Set your pickups to 3/32 on the bass side to start and see how it sounds!

Once this is done, plug in your guitar and see how it sounds. Does it sound better or worse than it did with the pickups where you originally had them? Continue to make adjustments to your pickups until you’ve reached a desired tone.

As mentioned above, you’ll want to be aware of the output balance between each pickup after making an adjustment. This is just as important as tone, in many cases. For example, let’s say you’ve swapped the stock bridge pickup in your Strat for a Seymour Duncan Hot Rails (a high-output single coil–sized humbucker). If you position this at the same height as the original pickup, chances are your guitar will be significantly louder at the bridge position than at other pickup settings. If this is not desired, you will need to compensate for this difference in output by either lowering the hotter bridge pickup or raising the middle and neck pickups closer to the strings to match the output of the bridge. This is why you will commonly see pickups sold as sets, where the manufacturer selects a set of pickups that typically work well together, both in output and tone.

Helpful Links

How to Change Strings on a Bass

Guitar Setup: How do I measure the action on my electric guitar?

How To Setup Your Electric Guitar Part 1: Adjusting the Truss Rod

The Great Standby Switch Myth

Solving Guitar Noise, Buzz and Hum